Sunday, May 29, 2011

Knit an iPod Case With a Carry Strap

This undertaking might appear daunting, but it is pretty simple. If you know the fundamentals of knitting, casting on and casting off, then you can do this challenge. It could include in a couple of new methods, like button holes and choosing up stitches, but these are as effortless as casting on.

Issues You will Require

    Yarn Knitting needles Button

    Swatch with the yarn and needles you Need to use for the undertaking.

    Figure out the width of your ipod. You Will need the case to be snug on the ipod so the width measurement is sufficient for the case.

    Seem at your swatch, and Establish how numerous stitches per inch You'll get. Multiply this by the width, in inches, of your ipod. This will give you the few stitches you Will need to cast on.

    Measure the duration all the way about the ipod, and include two inches additional for the leading flap. This is the duration that You may make the case. The case un-seamed is heading to seem to be like a plain rectangle or a small scarf.

    Make the button hole. When you get all around fifty percent an inch away from the completed duration of the task, you are heading to Require to cast off 5 stitches in the center of a row. This will type the initial 50 percent of the button hole. Make sure there are an equal handful of stitches on every single facet of these 5 so that the button hole is centered.

    Knit to the stitches that you bound off. There is heading to be a gap involving the stitches on the needle. Cast on 5 stitches, and knit the relaxation of the stitches on the needle. This completes the button hole.

    Proceed right up until the piece measure the proper duration, and cast off all the stitches.

    Fold the undertaking leaving the further two inches with the button hole for the cover flap, and seam up the 2 sides

    Decide on up a few stitches on a single aspect of the case. You Need these stitches to be at the edge of the cast on edge. If you seem carefully at the cast on edge, You may see that it varieties V's at the top rated of the edge. Slide your needle under these V's, and knit like you would generally. This will seamlessly Select up the stitches.

    Knit the strap the duration that you Require it.

    Cast off the 3 stitches, and attach the conclude of the strap to the other aspect of the case.

    Fold the flap over and mark wherever the button hole sits on the completed task. Sew the button at this spot to protected the case and conclude the undertaking.

Repair a Clicking 2nd Generation iPod Nano

The click on-wheel on a 2nd-era ipod nano will emit a "clicking" sound if dirt or dust has gotten into the seam in between it and the nano's casing.To obvious the click on-wheel of this undesired noise, partially disassemble the 2nd-era ipod nano and clear the click on-wheel. The technique calls for the Utilize of a number of family instruments, and will help save you the value and time misplaced from obtaining to get the nano into an approved support middle.

Items You may Will need

    Bath towel Utility knife Phillips jeweler's screwdriver Tweezers Flat-edged jeweler's screwdriver Glue stick Compressed air Lint-no cost cloth Distilled alcohol Cotton swabs

    Place a bath towel on a table. Place the 2nd-era ipod nano vertically faceup on the towel with the bottom going through you.

    Insert the suggestion of a utility knife into the seam at the bottom of the nano. Raise up on the suggestion to separate the bottom plate from the bottom. Pull the bottom plate off with your fingers. Take away the two visible screws from inside of the bottom with a Phillips jeweler's screwdriver.

    Insert the suggestion of the Phillips jeweler's screwdriver beneath the headphone jack at the excessive appropriate corner of the bottom. Elevate up on the suggestion to Lift the jack. Pull the jack out somewhat to reveal the screw concealed beneath it. Get rid of the screw with the Phillips jeweler's screwdriver.

    Pull the docking plate out of the bottom with your fingers. Pull the cable linked to the jack out from the circuit board utilizing tweezers.

    Insert the suggestion of the utility knife into the seam in between the upper plate and the nano's case at the upper left corner. Move the suggestion along the width of the nano to the proper side. Pull the upper plate off the nano's case.

    Get rid of the screw from every side of the leading with the Phillips jeweler's screwdriver.

    Place the suggestion of a flat-edged jeweler's screwdriver into the bottom of the nano. Push up to force the logic board out of the top rated. Grip the logic board coming out of the best and pull it the relaxation of the way out.

    Place the logic board on the bath towel. Insert the suggestion of the utility knife into the seam in between the click on-wheel and the nano's case.

    Rotate the suggestion about the click on-wheel in a complete circle. Raise up on the suggestion of the utility knife to Lift the click on wheel. Repeat this method on yet another edge of the click on-wheel. Grip the edge of the click on-wheel with the tweezers. Pull the click on-wheel off the logic board.

    Blow off the logic board with a burst of compressed air. Blow off the back again of the click on-wheel with a burst of compressed air. Wipe the edges of the click on-wheel with a clear edge of a lint-free of charge cloth.

    Moisten the suggestion of a cotton swab in distilled alcohol. Wipe the edges of the click on-wheel with the cotton swab. Dispose of the cotton swab in the trash.

    Moisten an additional cotton swab in distilled alcohol. Wipe all around the depression of the click on-wheel on the logic board with the cotton swab. Blow off the logic board with a burst of compressed air. Dispose of the cotton swab in the trash.

    Utilize a line of glue close to the edges of the click on-wheel with the glue stick. Place the glue stick back again into the depression on the logic board. Press down on the click on-wheel for a handful of seconds. Release the click on-wheel and let the glue set for ten minutes prior to proceeding.

    Insert the bottom of the logic board into the leading of the nano's case and push it back again in. Reattach the screw at the best. Pop the upper plate back again into the best of the nano.

    Reattach the cable from the docking plate back again into the logic board within the bottom of the nano with the tweezers.

    Place the docking plate back again into the bottom of the nano. Reattach the screw. Push the jack back again into its authentic place inside of the bottom of the nano. Reattach the two screws to the bottom. Pop the bottom plate back again onto the nano.

Make a Nano iPod Cover

You have acquired your ipod, which was almost certainly marketed by yourself. You have your headphones, and now you might be making an attempt to figure out what to do to defend it. You never Require your new toy to be scratched, dented or harmed if you drop it. A decently built cover can do just the trick.

Points You are going to Want

    Two squares of felt (shades of your selection) Needle and thread Straight pins Scissors Marker Paper one snap

    Trace your ipod onto a piece of paper for a template. You are going to Want to make the template with twice the duration and twice the thickness. The template need to have the very same width as your ipod; include some area for the flap.

    Trace your template onto the felt piece. Lower the felt piece, subsequent the template suggestions.

    Space the ipod in the middle of the Lower felt piece. Fold the bottom up so that it virtually addresses the ipod. Pin into space. Get rid of the ipod so you can straighten the pins and then space back again within to make positive you nevertheless have a snug in shape. When you might be positive, Get rid of the ipod.

    Lower any extra felt off the sides and spherical the corners of the flap by cutting off the edges.

    Sew the sides of the felt cover with each other. A buttonhole stitch will perform. Get rid of the pins As soon as full and flip within-out.

    Use the other piece of felt to Minimize out a rectangle matching the dimension of your ipod's display, a circle to match the dimension of your click on wheel and a more compact circle the dimensions of the click on wheel button. Stitch them into area onto your felt cover.

    Sew the best of the snap onto the inside of of the flap and sew the bottom fifty percent onto the inside of flap. Insert your ipod into the finished cover.