The click on-wheel on a 2nd-era ipod nano will emit a "clicking" sound if dirt or dust has gotten into the seam in between it and the nano's casing.To obvious the click on-wheel of this undesired noise, partially disassemble the 2nd-era ipod nano and clear the click on-wheel. The technique calls for the Utilize of a number of family instruments, and will help save you the value and time misplaced from obtaining to get the nano into an approved support middle.
Items You may Will need
- Bath towel Utility knife Phillips jeweler's screwdriver Tweezers Flat-edged jeweler's screwdriver Glue stick Compressed air Lint-no cost cloth Distilled alcohol Cotton swabs
Place a bath towel on a table. Place the 2nd-era ipod nano vertically faceup on the towel with the bottom going through you.
Insert the suggestion of a utility knife into the seam at the bottom of the nano. Raise up on the suggestion to separate the bottom plate from the bottom. Pull the bottom plate off with your fingers. Take away the two visible screws from inside of the bottom with a Phillips jeweler's screwdriver.
Insert the suggestion of the Phillips jeweler's screwdriver beneath the headphone jack at the excessive appropriate corner of the bottom. Elevate up on the suggestion to Lift the jack. Pull the jack out somewhat to reveal the screw concealed beneath it. Get rid of the screw with the Phillips jeweler's screwdriver.
Pull the docking plate out of the bottom with your fingers. Pull the cable linked to the jack out from the circuit board utilizing tweezers.
Insert the suggestion of the utility knife into the seam in between the upper plate and the nano's case at the upper left corner. Move the suggestion along the width of the nano to the proper side. Pull the upper plate off the nano's case.
Get rid of the screw from every side of the leading with the Phillips jeweler's screwdriver.
Place the suggestion of a flat-edged jeweler's screwdriver into the bottom of the nano. Push up to force the logic board out of the top rated. Grip the logic board coming out of the best and pull it the relaxation of the way out.
Place the logic board on the bath towel. Insert the suggestion of the utility knife into the seam in between the click on-wheel and the nano's case.
Rotate the suggestion about the click on-wheel in a complete circle. Raise up on the suggestion of the utility knife to Lift the click on wheel. Repeat this method on yet another edge of the click on-wheel. Grip the edge of the click on-wheel with the tweezers. Pull the click on-wheel off the logic board.
Blow off the logic board with a burst of compressed air. Blow off the back again of the click on-wheel with a burst of compressed air. Wipe the edges of the click on-wheel with a clear edge of a lint-free of charge cloth.
Moisten the suggestion of a cotton swab in distilled alcohol. Wipe the edges of the click on-wheel with the cotton swab. Dispose of the cotton swab in the trash.
Moisten an additional cotton swab in distilled alcohol. Wipe all around the depression of the click on-wheel on the logic board with the cotton swab. Blow off the logic board with a burst of compressed air. Dispose of the cotton swab in the trash.
Utilize a line of glue close to the edges of the click on-wheel with the glue stick. Place the glue stick back again into the depression on the logic board. Press down on the click on-wheel for a handful of seconds. Release the click on-wheel and let the glue set for ten minutes prior to proceeding.
Insert the bottom of the logic board into the leading of the nano's case and push it back again in. Reattach the screw at the best. Pop the upper plate back again into the best of the nano.
Reattach the cable from the docking plate back again into the logic board within the bottom of the nano with the tweezers.
Place the docking plate back again into the bottom of the nano. Reattach the screw. Push the jack back again into its authentic place inside of the bottom of the nano. Reattach the two screws to the bottom. Pop the bottom plate back again onto the nano.
No comments:
Post a Comment